ENGLISH
ENGLISH
DEUTSCH
ESPAÑOL
FRANÇAIS
ITALIANO
NEDERLANDS
Establishing a Connection to the User Interface of the Product
Information on establishing a connection
Connection in the local network
Direct connection via Wi-Fi
WPS function
Design of the User Interface
Information on establishing a connection
Table of Contents
toggle menu
Information on this Document
Validity
Target Group
Contents and structure
Levels of Warning Messages
Symbols in the Document
Typographies in the document
Designations in the Document
Additional Information
Safety
Intended Use
IMPORTANT SAFETY INSTRUCTIONS
Scope of Delivery
Scope of delivery of Charging Station Column
Product overview
Device function
System Overview
SMA eCharger in Stand-Alone Mode
SMA eCharger with Sunny Home Manager
SMA eCharger with SMA Data Manager M
Circuitry Overview
Communication Overview
Product Description
Symbols on the Product
Interfaces and Functions
User Interface
Device Key (DEV KEY)
SMA PUK2.0
Digital inputs
Modbus
SEMP protocol
Grid Management Services
SMA Smart Connected
SMA Speedwire
Wi-Fi
Wi-Fi connection to SMA 360° app and SMA Energy app
RS485 interface
Multifunction relay (MFR)
Charging release
Knock sensor
LCD
LED Signals
Mounting
Requirements for Mounting
Requirements for the Mounting Location
Permitted and prohibited mounting positions
Dimensions for mounting
Recommended clearances for mounting
Wall Mounting
Mounting the Charging Station Column
Electrical Connection
Requirements for the electrical connection
Permitted grid configurations
Residual-current monitoring unit
Load-break switch and cable protection
Overvoltage category
AC cable requirements
Network cable requirements
Signal cable requirements
Requirements for the RS485 interface
Overview of the Connection Area
Electrical connection procedure
Connecting the Utility Grid
Multi-EVC operation
Multi-EVC operation
Connecting the AC Cable
Connecting the Network Cables
Connecting the Ripple Control Receiver
Digital input DI 1-4
Pin assignment DI 1-4
Circuitry overview DI 1-4
Connecting the ripple control receiver to DI 1-4
Connection to digital input DI 5-6
Digital input DI 5-6
Pin assignment DI 5-6
Circuitry overview DI 5
Circuitry overview DI 6
Connecting Signal Source to Digital Input DI 5-6
Connection to the Multifunction Relay
Digital output (MFR)
Pin assignment MFR
Connect signal source to MFR
Controlling the loads via multifunction relay
Connecting to the RS485 interface
RS485 input
RS485 pin assignment
Connecting RS485
Close the enclosure cover.
Commissioning
Procedure for commissioning in combination with Sunny Home Manager 2.0
Procedure for commissioning in secure power supply operation
Procedure for connecting to the SMA Data Manager M
Procedure for device configuration
Commissioning the Product
Transfer to the operator
Operation
Design of the User Interface
Establishing a Connection to the User Interface of the Product
Information on establishing a connection
Connection in the local network
Access addresses for the product in the local network
Ports for data communication in the local network
Establishing a Connection via Ethernet in the local network
Establishing a Connection via WLAN in the Local Network
Direct connection via Wi-Fi
Connection options for Wi-Fi direct connection
Access information for direct Wi-Fi connection
Establishing a direct Wi-Fi connection with WPS
Establishing direct Wi-Fi connection with Wi-Fi network search
WPS function
Connection options with WPS
Activating WPS for automatic connection
Activating WPS for direct connection to a smart device
Configuring Service Access
User Management
Access rights to the user interface
Add new user
Changing User Rights or User Information
Delete user accounts
Device Administration
Register Devices
Delete devices
Configure device
Modbus
SMA Modbus Client Profile
Creating a New Modbus Client Profile
Registering a New Modbus Device and Assigning a Modbus Profile
Changing parameters
I/O configuration
Digital output (MFR)
Use of the digital output (MFR)
Configure the digital output (MFR)
Configuring the fast stop function
Update and backup
Automatically Updating the Firmware
Performing a Manual Firmware Update via the User Interface
Function and content of the backup file
Creating a Backup File
Resetting the product to default setting
Activating the Charging Release
Teaching RFID cards
Set ambient lighting
Starting and Ending the Charging Process
Properties of Charging Modes
Authorizing the charging process via RFID card
Authorizing the charging process via Energy App
Ending the Charging Process
Disconnecting the product from voltage sources
Maintenance
Cleaning
Troubleshooting
Create Diagnostics Data
Event messages
Event 901
Event 1302
Event 1416
Event 3701
Event 6202
Event 6501
Event 6603
Event 6630
Event 7001
Event 7312
Event 7320
Event 7321
Event 7330
Event 7333
Event 7347
Event 7348
Event 7605
Event 7609
Event 7619
Event 7637
Event 7639
Event 7702
Event 8003
Event 8709
Event 8710
Event 9026
Event 9102
Event 9801
Event 9802
Event 9803
Event 9804
Event 9805
Event 9806
Event 9807
Event 9808
Event 9809
Event 9810
Event 9811
Event 9812
Event 9813
Event 9814
Event 9815
Event 9905
Event 9908
Event 9909
Event 10002
Event 10005
Event 10100
Event 10101
Event 10107
Event 10109
Event 10111
Event 10114
Event 10207
Event 10222
Event 10270
Event 10283
Event 10284
Event 10285
Event 10286
Event 10294
Event 10295
Event 10321
Event 10507
Event 10603
Event 10612
Event 27201
Event 27204
Event 27205
Event 27206
Event 27208
Event 27313
Decommissioning the Product
Replacing the Product
Disposal
Technical Data
Inputs and outputs (AC)
Communication
Protective Devices
General Data
Equipment
Digital inputs
Digital output (multifunction relay)
Data Storage Capacity
Climatic Conditions
Torques
Accessories
Contact
EU Declaration of Conformity
