ENGLISH
ENGLISH
DEUTSCH
ESPAÑOL
FRANÇAIS
LIETUVIŠKAI
NEDERLANDS
POLSKI
PORTUGUÊS
SVENSKA
TÜRKÇE
Connection to the voltage supply X1
Voltage supply X1
PIN assignment X1
Circuitry overview X1
Connecting the voltage supply to X1
Connecting network cables to X4/X5
Voltage supply X1
Table of Contents
toggle menu
Important information
Information on this Document
Validity
Target Group
Content and Structure of this Document
Levels of Warning Messages
Symbols in the Document
Typographies in the document
Designations in the Document
Additional Information
Safety
Intended Use
IMPORTANT SAFETY INSTRUCTIONS
Scope of Delivery
Product overview
Overview of compatible products
Product Description
Symbols on the Product
Reset button
LED Signals
Network Port LEDs
Interfaces and Functions
SMA Speedwire
Modbus
SunSpec Modbus
User Interface
Sunny Portal
Dashboard
Plant-wide parameterization
Energy Monitoring
FTP push
SMA Smart Connected
Grid Management Services
Reactive Power Control
Zero export
Active Power Limitation
Direct selling
Device key (WPA2-PSK)
Mounting
Requirements for Mounting
Requirements for the Mounting Location
Permitted and prohibited mounting positions
Dimensions for mounting
Recommended clearances for mounting
Mounting the Product on the DIN Rail
Mounting the Product on the Wall
Connection
Requirements for the Connection
RS485 X2 cable requirements
Network cable requirements
Connection cable requirements for power supply terminal X1
Overview of the Connection Area
Preparing the Connection Cable
Connection to the RS485 X2 input
RS485 input X2
PIN assignment X2
Connecting RS485 devices to X2
Replacing SMA Com Gateway with RS485 Devices
Connection to digital input X3
Digital inputs X3
PIN assignment X3
Circuitry overview X3
Connecting signal source to X3
Connection to the system network X4/X5
System network X4/X5
Connecting network cables to X4/X5
Connection to the voltage supply X1
Voltage supply X1
PIN assignment X1
Circuitry overview X1
Connecting the voltage supply to X1
Commissioning
Requirements for Commissioning
Changing the Network Configuration
Starting the Installation Assistant
Establishing a Connection to the User Interface
Connection in the local network
Access addresses for the product in the local network
Ports for data communication in the local network
Establishing a connection in the local network
Direct connection via Wi-Fi
Connection options for Wi-Fi direct connection
Access information for direct Wi-Fi connection
Establishing a direct Wi-Fi connection by entering the Wi-Fi data
Establishing a direct Wi-Fi connection by scanning the QR code
Registration in Sunny Portal
Profiles for data communication
Register as a new user in Sunny Portal
Log in to Sunny Portal as an existing user
Create new PV system
Add product to an existing system
Operation
Design of the User Interface
Access rights to the user interface
Device Administration
Register Devices
Delete devices
Backup file
Function and content of the backup file
Creating a Backup File
Upload backup file
Resetting the product to default setting
Delete user accounts
Configuring Service Access
Energy management
Activating the energy management
Deactivating the energy management
Set battery fallback behavior when energy management is disabled
Predefined operating modes
Available operating modes
Add new operating mode
Setting options for peak load shaving
Create a new schedule
Export schedules
Import schedules
Firmware Update
Automatically Updating the Firmware
Automatically updating the firmware of connected devices
Performing a Manual Firmware Update via the User Interface
Carrying out a manual firmware update using a USB flash drive
Carrying out a manual firmware update of connected devices using a USB flash drive
Grid management service
Active Power Limitation
Configuring active and reactive power setpoints
Configure additional specifications from the grid operator for the country data set.
Configure additional direct seller's specifications for the country data set.
Setting Zero Export
Modbus
SMA Modbus Client Profile
SunSpec Modbus client profile
Creating a New Modbus Client Profile
Registering a New Modbus Device and Assigning a Modbus Profile
Limiting-value based switching
Operators for limit-based switching
Parameter for limit-based switching
Switch digital outputs based on thresholds
Reference values for threshold-based switching
Separated reference values for the active power limitation
Speedwire encryption
Speedwire Encryption of the System Communication
Enabling Speedwire Encryption
Fallback Behavior
Function of the fallback behavior
Fallback behavior in the event of communication failure to the digital inputs
Fallback behavior in the event of communication failure to the energy meter at the point of interconnection
Fallback behavior in reactive power mode
SG Ready interface
Configuration of SG Ready interface
Example: Control of a heat pump by SMA Data Manager M
Troubleshooting
Obsolete or incorrect measured values are displayed
Not all devices are being detected
The product user interface cannot be called up
Parameter changes via the device settings or a parameter adjustment are not confirmed
The product cannot be registered in Sunny Portal
The firmware of a connected SMA product was not updated during a firmware update
No data are displayed on the user interface of the product
Create Diagnostics Data
Carry out reset
Decommissioning the Product
Technical Data
Communication
Connections
Voltage supply
Climatic Conditions
General Data
Digital inputs
Equipment
Accessories
EU Declaration of Conformity
Compliance Information
Contact
